Flexsim新模型-“Heatmap Module ”

原帖地址：http://www.flexsim.com/community/forum/showthread.php?t=2881

下载模型可以去原帖上面进行~~~
; B+ V$ V2 C0 J
5 T' R) u" V# q3 `7 W4 \7 c节选里面的模型作用介绍
“Hi community!
I've a little something for you ;-) I've developed a little module to show a heatmap in our models. It's brandnew and still beta but I'm interested in our opinion.
" L* o. r* T1 @" S7 ~$ p6 d6 j# ~
& u: J" L# [: ~# n" b1 x4 s$ Z' }
Restrictions for this beta:
( z9 R) w$ E2 {3 i& I - no gui
# |+ O7 L2 T5 T" u - only for 64 bit
- tested only with FlexSim GP 7.1.4 64bit on a Windows 7 64bit
1 b- j* s3 h: T! `

- y! X2 C* Z% R1 ~" k% w How to install?
% _- x; Y: K$ J2 W$ K. U6 d$ D Unzip file to modules folder in flexsim.
6 S3 K; Y. |2 H
* J/ _) a4 d! f  C' h! o
! x% C- q3 h5 |& _! P0 A* }% g8 E How to use?
$ @; J6 Q' c$ E* T Just drag your new HeatmapTicker object into your model. That's it.
3 \' {; y7 W, T+ ~. P+ @
% T! Z3 _! B# r7 m
3 e% @) b5 _  T( u5 ^8 z What does this module?
5 B6 i( L# Q. `0 y1 d( v: O This module draw a heatmap in your model. It collects the location of your taskexecuters for each tick of the heatmapticker. This shows you how often a location was used. Red means a hot area and blue a cold area.
Which settings options are available?
$ ~9 v9 q8 E( k' P0 ?8 P Even without a gui you have several options to configure your heatmap. You have to access your heatmapticker with the tree view. The settings are in the variables node:
- ticktime -> time interval to add the actual location of your taskexecuters
- gridsizeX -> area in x to summarize locations
- gridsizeY -> area in y to summarize locations
- sizeZ -> if greater than 0, your heatmap goes up in the sky
: q. G, A6 Q* g! s; d/ Z1 l - objectList -> only for your information, which taskexecuters are registered for the heatmap (robot and elevators aren't added)
$ z+ D1 X) W5 d  G! w( o - mesh -> heatmap drawing, don't touch
5 H( o& p4 D  G+ U You can make you heatmap invisible if you use the flexsim command switch_hideshape.
; }' F2 t: j9 S9 S
6 L, d3 A. T1 j
Hints:
- very small ticktime, gridsizeX and/or gridsizeY boost your cpu usage
- only taskexecuters in the model tree will be recognized
- only used locations will be stored -> no restrictions for locations
9 w; @7 b8 U& S8 P - the colors and optional heights aren't linear -> a natural logarithm will be used with the measured data to make the heatmap more visible
' t* s9 ~2 e& C, c& a
* X9 V1 h3 H% c7 Y" w I'm curious about your thoughts and hints. Of course you'll get the final version also. Did I mentioned that it's free?
”

好东西，flexsim真强大啊！

狂霸酷帅拽。

强大，谢谢楼主！